Common signs include damage to the outer covering, delayed accelerator response time, and problems with cruise control.

Table of Contents

How do I know if my throttle cable is bad?

Common signs include damage to the outer covering, delayed accelerator response time, and problems with cruise control.

How long do throttle cables last?

How long you can expect your accelerator cable to last will depend in large measure on how often you drive. The more use the accelerator cable gets, the more prone it is to wear and tear. Usually, you can expect to get five years from your accelerator cable before it needs to be replaced.

How much does it cost to fix a throttle cable?

CarsEstimateAverage Dealer Price2006 Ford Taurus$198$210.822012 Kia Optima$199$211.142006 Acura TL$245$257.222006 Acura RSX$327$339.90

When should I replace throttle cable?

Replacing your throttle cables. If your inspection reveals any damage, you’ll need to replace your throttle cables. You might also need to replace them to accommodate a different handlebar.

👉 For more insights, check out this resource.

How much does it cost to fix an accelerator?

The average accelerator pedal sensor replacement cost is between $100 and $300, depending on the car model and labor costs. The accelerator pedal sensor usually costs between $50 and $200. The labor cost can range from $50 to $100 at a workshop.

What do throttle cables do?

Your car’s accelerator cable, also known as a throttle cable, is a braided metal wire that connects the gas pedal to the engine throttle plate. By applying and releasing pressure on the gas pedal, the driver is able to control the speed of the car.

👉 Discover more in this in-depth guide.

How long does clutch cable last?

That being said it should be replaced every 2 to 3 years to prevent being stuck on the side of the road with a snapped cable when all the dealers are closed and you can’t get a cable.

What is throttle free play?

In simple words, throttle free play is a short bit of movement at the beginning of the throttle twist that has no effect. That free play allows you to bring the throttle open smoothly, and gently. It simply acts as a dead zone just like you start pulling a rope from one end.

When should I change my bike accelerator cable?

One usually replaces a cable when the wire strands start breaking by the pull or they can’t be adjusted out anymore to take up the slack caused by the wire strands stretching. It’s wise to carry an extra clutch and brake cable (if used) on the bike at all times since cables can and do fail regardless of age.

Article first time published on

How do I check my throttle cable?

Step 1: Locate the throttle cable. One end of the throttle cable is located in the engine compartment, attached to the throttle body. The other end is on the driver’s side floor, attached to the accelerator pedal.

Why is my throttle cable stuck?

A sticky throttle could be caused by worn cables, lack of lubrication in the cables or the cable getting bound up somewhere in the mechanism. Or it can be caused by an issue with the carburetor or EFI. … If the screws in the throttle housing are too tight it could cause the cable to stick.

Is it safe to drive with a bad throttle body?

You might be wondering—is it safe to drive with a bad throttle body? The quick answer is no. Once it starts to show signs of going bad or being clogged, you should address the problem right away. Otherwise the vehicle may stall or fail to accelerate, creating a safety hazard.

What causes accelerator failure?

Clogged or dirty fuel filter – A dirty filter, clogged with debris and other impurities will hinder the engine’s ability to receive the proper amount of fuel. … If the fuel pump gives out or becomes clogged, it will be unable to supply fuel to the injectors and may result in poor acceleration, sputtering, or stall outs.

How much is a new gas pedal?

The entire replacement process will cost you between $130 and $200. Labor costs don’t have much of a range- somewhere between $70 and $90. But the parts may cost you as little as $50 or as much as $120+.

How much slack should a throttle cable have?

Most motorcycle manufacturers recommend about 2 to 3 millimeters of throttle free play, but over time the cables will stretch and settle into their housings and you’ll end up with more slack.

How tight should the throttle cable be?

The accelerator cable tension is usually set so that 2-3mm of free play is present in the throttle grip. Once the correct tension has been applied, the lock nuts should be snugged and any dust covers should be slid back over the adjusters. Cables can be adjusted using the appropriate size wrench.

Why does my car have two throttle cables?

Premium Member. zenbike said: Does bring up an interesting thought of removing the auto return spring and then having the ability to control closing the throttle as well as opening it. Feel like there was a good name for this system from old Harley bikes.

Can you solder stainless steel cable?

Unlike other metals, stainless steel is very difficult to solder. It has a thick oxide layer that prevents melted solder from sticking to its surface.

Can you drive a car with a broken clutch cable?

Warning: Driving your car while the clutch is broken will quite likely cause further damage either to the clutch, the gearbox, the shifter, or your starter motor. Use it as a last resort only.

How do you know if your clutch cable is broken?

Clutch Pedal Remains Stuck to the Floor. Clutch Pedal Feels Loose or Spongey. Clutch Pedal is Hard to Engage. Transmission Makes A Grinding, Whirling or Chirping Noise in Neutral.

Why does a clutch cable break?

Over time, the clutch cable can become stretched or broken which can cause the clutch to quit working properly. If the clutch pedal feels hard and resists being pressed down, the clutch pedal has gone bad. If you keep pressing the pedal, the cable is liable to break.

Why do motorcycles have 2 throttle cables?

So why do some motorcycles have two throttle cables? The previous throttle grip arrangement of operating the spring loaded slide mechanism by a single pull cable was found to be inadequate. That’s why, dual or double cable system throttle grip system was invented to favor twin-cylinder motorcycles in particular.

Why is my bike lagging?

Poor timing is usually caused by a fault in the electrical system or the cam on the mechanical timing system could be faulty. Also, if you or someone else has messed with the timing before, that could also cause timing issues.